울타리 피켓 간격
100% 무료 시공 전문가 & DIY 펜스 계산기

울타리 피켓 간격 및 수량 계산기

목재, 합성목재, 알루미늄 펜스 시공 시 판자 수량, 오차 없는 균등 간격, 중심 간격(피치) 및 여유 자재량을 밀리미터 단위로 정확하게 산출합니다.

빠른 프리셋:
ft
in
in
in
자재 휨, 옹이, 절단 파손에 대비한 여유분
%
#
필요 판자 수량
17개

여유분 포함 총합:19 개

정밀 계산 간격
2 1/16"

2.028"|51.5 mm

중심 간 피치 (Pitch)
5 9/16"

5.528"|140.4 mm

구간별 세부 치수
판자 차지 길이:59.50" (1511mm)
틈새 차지 길이:36.50" (927mm)
양쪽 끝단 틈:2 1/16" (2 gaps)
Physical Screen RulerDefault Estimate

Measures physical gaps & spacers directly on screen. Calibrate for true 1:1 scale matching.

Pos:

Interactive Picket Layout Diagram

(Swipe horizontally to inspect)
|
Fence layout visualization.
Fence Pickets (0)
Equal Gaps (0)
Post Ends
P = 0"(Center Pitch)
Community Suggestions & Bug Reports

Have a Suggestion or Found an Issue?

Did you spot an error in the calculation, or have a recommendation to make this tool better for carpenters and DIY builders? Describe your idea or issue below and send it directly to our developer team.

Sent directly to: hello@fencepicketspacingcalculator.com

fx

Step-by-Step Mathematical Explanation & Formulas

See how your picket quantity, exact gap, and pitch were derived.

[+] Expand
Real-World Worked Example

Worked Example: 8-Foot Fence Panel Picket Spacing

Walkthrough of a standard 8-foot (96-inch) wood fence panel built with standard 3.5-inch nominal pickets.

1. Input Parameters
  • Fence Run (L): 8 ft = 96.0 inches
  • Picket Width (w): 3.5 inches (1x4 nominal)
  • Target Gap (g): 2.0 inches
  • Layout: Equal End Gaps
2. Step 1: Picket Count

For equal end gaps, there are n + 1 gaps.
n = (96 - 2) / (3.5 + 2) = 17.09Rounding to nearest whole number yields 17 pickets.

3. Step 2: Exact Fit Gap

Total picket width = 17 × 3.5" = 59.5".
Remaining gap span = 96" - 59.5" = 36.5".
Divided over 18 gaps: 2.028" (2 1/16").

Final Layout Summary17 Pickets @ 3.5" width | 18 Gaps @ 2 1/16" exact spacing | Pitch: 5 9/16"
Try Preset →
Contractor & DIY Field Guide

Practical Measurement & Calibration Guide

Avoid costly timber waste and layout mistakes by following professional measurement best practices.

1Measure Inside Clear Span (Between Posts)

Always measure the distance between the inside faces of your fence posts, not center-to-center. Measure both at the top rail and bottom rail level to check for post plumbness or bowing.

2Use Actual (Not Nominal) Picket Widths

Lumber sizes are nominal. A standard “1x4” wood picket actually measures 3.5 inches wide, and a “1x6” picket measures 5.5 inches wide. Always measure your physical pickets before calculating.

3Cut a Wooden Spacer Block

Once the calculator gives your exact gap (e.g. 2 1/16"), cut a small wooden scrap block to that exact width. Use it as a physical spacer between pickets during installation for uniform alignment without measuring every gap.

4Check Swimming Pool Safety Codes

If building a fence around a swimming pool, IRC safety codes mandate that vertical gaps between pickets must not exceed 4 inches (102 mm) to prevent child passage. Use Mode 2 (Even Spacing with Max Gap) set to 4.0".

자주 묻는 질문

자주 묻는 질문

울타리 판자 간격 계산, 안전 기준 및 시공 노하우에 대한 자주 묻는 질문입니다.

울타리 판자 사이 간격은 어떻게 계산하나요?

+

기둥 사이 안쪽 치수 L에서 판자 전체 폭(n × w)을 뺀 뒤, 틈새 개수로 나눕니다. 양 끝도 동일하게 띄울 경우: 간격 = (L - n × w) / (n + 1) 입니다.

펜스 판자 사이 틈새는 몇 cm가 적당한가요?

+

시선 차단용 사생활 보호 펜스는 10mm~20mm(1~2cm), 일반 정원 펜스는 30mm~50mm(3~5cm)를 주로 사용하며, 안전 난간은 최대 100mm를 넘지 않아야 합니다.

판자를 오차 없이 균일하게 시공하는 노하우는?

+

본 계산기로 산출된 정확한 틈새 치수로 폐목재를 잘라 간격재(스페이서 블록)를 만듭니다. 판자를 붙일 때마다 이 간격재를 끼우고 피스를 체결하면 완벽한 간격이 유지됩니다.

울타리 판자는 몇 장을 구매해야 하나요?

+

전체 길이 ÷ (판자 너비 + 목표 간격)으로 수량을 산출한 후, 판자의 휨, 옹이 불량 및 재단 손실을 고려하여 5%~10%의 여유분을 추가 주문하세요.

1x4 목재의 실제 치수는 얼마인가요?

+

1x4 목재의 실제 너비는 89mm(두께 19mm)입니다. 1x6 목재의 실제 너비는 140mm입니다. 호칭 규격과 실측 치수가 다름에 유의하세요.