울타리 피켓 간격
가이드

Fence Picket Spacing & Installation Field Guide

Master the engineering math, physical spacing methods, IRC pool safety codes, and nominal lumber rules for installing beautiful, long-lasting picket fences.

시공 전문가 & 셀프 인테리어 가이드

울타리 피켓(살) 완벽 가이드: 간격 계산, 규격 치수 및 자재 산출

목재 펜스, 데크 난간, 방부목 울타리의 판자 간격을 밀리미터 단위로 균등하게 배치하고 시공하는 실전 지침서입니다.

울타리 피켓이란 무엇이며 왜 정확한 간격 계산이 중요한가?

피켓(Picket)은 울타리의 기둥과 가로 레일 사이에 일정한 간격으로 부착되는 수직 판자 또는 난간 살을 뜻합니다. 방부목, 천연 하드우드, 합성목재, 알루미늄 등 어떤 자재를 사용하든 오차 없는 간격 배치가 완성도를 결정합니다.

시공 현장에서 눈대중으로 시공하면 마지막 기둥에 이르러 틈새가 너무 좁아지거나 넓어지는 시공 하자가 발생합니다. 본 계산기는 기둥 안쪽 실제 개구 폭과 판자 실측 너비를 기준으로 모든 틈새가 한 치의 오차도 없이 동일하게 맞물리도록 산출합니다.

목재의 호칭 치수(규격명)와 실제 실측 치수의 차이

목재는 대패 가공(S4S)을 거치며 규격명보다 실제 치수가 작아집니다. 예를 들어 북미 표준 1x4 규격 목재의 실제 너비는 89mm(3.5인치)이며, 1x6 규격은 140mm(5.5인치)입니다. 계산 전 반드시 버니어캘리퍼스나 줄자로 실측하세요.

판자 규격 및 자재 종류호칭 규격명실제 너비 (실측)실제 두께
표준 방부목 / 시더 1x41" × 4"89 mm (3.5인치)16 ~ 19 mm
광폭 방부목 / 시더 1x61" × 6"140 mm (5.5인치)16 ~ 19 mm
합성목재(WPC) 피켓표준 규격120 ~ 150 mm12 ~ 20 mm
알루미늄 각파이프 난간살20 × 20 mm20 ~ 30 mm알루미늄 중공관

울타리 균등 간격 계산 공식 (수학적 원리)

기둥 사이 총 안쪽 길이에서 모든 판자의 폭 합계를 뺀 후, 나누어야 할 틈새의 개수로 나누어 계산합니다.

양 끝단 균등 틈새 기준 (기둥과 판자 사이도 동일한 틈 유지):

간격 = (L - n × w) / (n + 1)

L은 기둥 안쪽 개구 폭, n은 판자 개수, w는 판자 실측 너비입니다. n개의 판자를 놓으면 틈새는 n + 1개가 됩니다.

기둥 밀착 배치 기준 (첫 장과 끝 장이 기둥에 닿음):

간격 = (L - n × w) / (n - 1)

양 끝 판자를 기둥 면에 밀착시킬 경우 판자 사이의 내부 틈새는 n - 1개가 됩니다.

안전 기준 및 규정 준수 (추락 방지 규격)

수영장 울타리 및 발코니 난간 규정에서는 유아의 머리 끼임이나 통과를 방지하기 위해 수직 판자 사이의 유효 간격을 100mm(약 4인치) 이하로 엄격히 제한하고 있습니다.

자재별 특징: 방부목, 천연목재, 합성목재, 알루미늄

방부목은 경제적이지만 주기적인 오일스테인 도장이 필요합니다. 합성목재와 분체도장 알루미늄은 썩거나 뒤틀림이 없어 유지 관리가 거의 필요하지 않습니다.

Contractor & DIY Field Guide

Practical Measurement & Calibration Guide

Avoid costly timber waste and layout mistakes by following professional measurement best practices.

1Measure Inside Clear Span (Between Posts)

Always measure the distance between the inside faces of your fence posts, not center-to-center. Measure both at the top rail and bottom rail level to check for post plumbness or bowing.

2Use Actual (Not Nominal) Picket Widths

Lumber sizes are nominal. A standard “1x4” wood picket actually measures 3.5 inches wide, and a “1x6” picket measures 5.5 inches wide. Always measure your physical pickets before calculating.

3Cut a Wooden Spacer Block

Once the calculator gives your exact gap (e.g. 2 1/16"), cut a small wooden scrap block to that exact width. Use it as a physical spacer between pickets during installation for uniform alignment without measuring every gap.

4Check Swimming Pool Safety Codes

If building a fence around a swimming pool, IRC safety codes mandate that vertical gaps between pickets must not exceed 4 inches (102 mm) to prevent child passage. Use Mode 2 (Even Spacing with Max Gap) set to 4.0".

Real-World Worked Example

Worked Example: 8-Foot Fence Panel Picket Spacing

Walkthrough of a standard 8-foot (96-inch) wood fence panel built with standard 3.5-inch nominal pickets.

1. Input Parameters
  • Fence Run (L): 8 ft = 96.0 inches
  • Picket Width (w): 3.5 inches (1x4 nominal)
  • Target Gap (g): 2.0 inches
  • Layout: Equal End Gaps
2. Step 1: Picket Count

For equal end gaps, there are n + 1 gaps.
n = (96 - 2) / (3.5 + 2) = 17.09Rounding to nearest whole number yields 17 pickets.

3. Step 2: Exact Fit Gap

Total picket width = 17 × 3.5" = 59.5".
Remaining gap span = 96" - 59.5" = 36.5".
Divided over 18 gaps: 2.028" (2 1/16").

Final Layout Summary17 Pickets @ 3.5" width | 18 Gaps @ 2 1/16" exact spacing | Pitch: 5 9/16"
Try Preset →
fx

Step-by-Step Mathematical Explanation & Formulas

See how your picket quantity, exact gap, and pitch were derived.

[+] Expand
Interactive Tool

Calculate Your Fence Run Now

Plug your post span and picket dimensions into our interactive tool to get instant results and a visual blueprint.

간격 계산하기 →