フェンス板間隔
完全無料 プロ施工&DIY対応フェンス計算機

ウッドフェンス間隔・枚数計算機

フェンスの全長と板幅から、均等な隙間間隔、芯々ピッチ、必要枚数、ロス率をミリ単位で瞬時に自動計算します。

クイック設定:
ft
in
in
in
反りや割れ、カットミスへの備え
%
#
必要な板の枚数
17枚

ロス込み合計:19 枚

正確な隙間幅
2 1/16"

2.028"|51.5 mm

芯々ピッチ (中心間距離)
5 9/16"

5.528"|140.4 mm

スパン内訳
板の合計幅:59.50" (1511mm)
隙間の合計幅:36.50" (927mm)
両端の隙間:2 1/16" (2 gaps)
ご提案・不具合報告
Physical Screen RulerDefault Estimate

Measures physical gaps & spacers directly on screen. Calibrate for true 1:1 scale matching.

Pos:

Interactive Picket Layout Diagram

(Swipe horizontally to inspect)
|
Fence layout visualization.
Fence Pickets (0)
Equal Gaps (0)
Post Ends
P = 0"(Center Pitch)
Community Suggestions & Bug Reports

Have a Suggestion or Found an Issue?

Did you spot an error in the calculation, or have a recommendation to make this tool better for carpenters and DIY builders? Describe your idea or issue below and send it directly to our developer team.

Sent directly to: hello@fencepicketspacingcalculator.com

fx

Step-by-Step Mathematical Explanation & Formulas

See how your picket quantity, exact gap, and pitch were derived.

[+] Expand
Real-World Worked Example

Worked Example: 8-Foot Fence Panel Picket Spacing

Walkthrough of a standard 8-foot (96-inch) wood fence panel built with standard 3.5-inch nominal pickets.

1. Input Parameters
  • Fence Run (L): 8 ft = 96.0 inches
  • Picket Width (w): 3.5 inches (1x4 nominal)
  • Target Gap (g): 2.0 inches
  • Layout: Equal End Gaps
2. Step 1: Picket Count

For equal end gaps, there are n + 1 gaps.
n = (96 - 2) / (3.5 + 2) = 17.09Rounding to nearest whole number yields 17 pickets.

3. Step 2: Exact Fit Gap

Total picket width = 17 × 3.5" = 59.5".
Remaining gap span = 96" - 59.5" = 36.5".
Divided over 18 gaps: 2.028" (2 1/16").

Final Layout Summary17 Pickets @ 3.5" width | 18 Gaps @ 2 1/16" exact spacing | Pitch: 5 9/16"
Try Preset →
Contractor & DIY Field Guide

Practical Measurement & Calibration Guide

Avoid costly timber waste and layout mistakes by following professional measurement best practices.

1Measure Inside Clear Span (Between Posts)

Always measure the distance between the inside faces of your fence posts, not center-to-center. Measure both at the top rail and bottom rail level to check for post plumbness or bowing.

2Use Actual (Not Nominal) Picket Widths

Lumber sizes are nominal. A standard “1x4” wood picket actually measures 3.5 inches wide, and a “1x6” picket measures 5.5 inches wide. Always measure your physical pickets before calculating.

3Cut a Wooden Spacer Block

Once the calculator gives your exact gap (e.g. 2 1/16"), cut a small wooden scrap block to that exact width. Use it as a physical spacer between pickets during installation for uniform alignment without measuring every gap.

4Check Swimming Pool Safety Codes

If building a fence around a swimming pool, IRC safety codes mandate that vertical gaps between pickets must not exceed 4 inches (102 mm) to prevent child passage. Use Mode 2 (Even Spacing with Max Gap) set to 4.0".

よくある質問

よくある質問

フェンス板の間隔計算、建築基準、DIY施工に関するよくある質問と回答です。

ウッドフェンスの板の隙間はどのように計算しますか?

+

柱間の実測スパンLから、板の合計幅(枚数n × 板幅w)を引き算し、隙間の総数で割ります。両端も均等に空ける場合:隙間 = (L - n × w) / (n + 1) となります。

フェンスの板同士の間隔は何cm空けるのが一般的ですか?

+

目隠しフェンスでは10mm〜20mm程度、通風や日当たりを重視する格子フェンスでは30mm〜50mm程度が一般的です。安全柵では100mm以下にします。

板をきれいに等間隔で取り付けるコツは?

+

当計算ツールで割り出した隙間幅の寸法で端材(当て木・スペーサーブロック)を正確にカットし、板と板の間に挟みながらビス留めしていくと狂いなく均等に施工できます。

フェンスの板は何枚買えば良いですか?

+

スパン全長 ÷ (板幅 + 希望の隙間) で概算枚数を出し、木材の反りや節、カット失敗を考慮して5%〜10%の予備(ロス分)を追加購入することをおすすめします。

1x4材の実寸の幅は何mmですか?

+

1x4(ワンバイフォー)材の実寸幅は89mm(厚み19mm)です。1x6材の実寸幅は140mmです。呼び寸法と実寸が異なる点にご注意ください。